Prefabricated pool construction
We manufacture the prefabricated pool shell in the factory, and install it on site within days.

Prefabricated pool construction process
01 / 04
Excavation and raft
Days 2-4- 01
- 02
- 03
- 04
Çilek Havuz in prefabricated pool construction
We run prefabricated pools with the same engineering discipline as reinforced concrete pools.
A single team handles the survey, ground preparation, assembly and commissioning; the quotation is itemised line by line.
- Year founded
- 1998
- Years of industry experience
- 33+
- Export countries
- 14
- Workmanship warranty
- 2
// 01 · Decision
A prefabricated pool decision starts with four questions, and the system follows from the answers.
The quality of a prefabricated pool is set by the size, access and system decisions made before the shell reaches the site. We first clarify how the pool will be used, then how far the site allows trucks, cranes and ground loads.

01
Users and size of the pool
The most common depth for residential pools is 1.40-1.50 m; an adult can stand, and it is deep enough for swimming. Whether the pool is for swimming or cooling off sets the size, and the size sets the water volume and equipment.
- Swimming, cooling off or hotel use
- Constant depth of 1.40-1.50 m
- Water volume and bather capacity
02
What the site allows
A one-piece shell needs a truck and a crane; a narrow street, a low power line or a tree can block that route. Panels arrive in sizes that can be carried by hand. Groundwater and soil bearing capacity are assessed on site during the survey.
- Garden entrance and crane access
- Soil bearing capacity and groundwater
- Plant room location
03
Panel, monoblock or stainless steel
The panel system gives flexibility in size and is finished with a liner. The monoblock polyester shell comes from the mould in one piece with a gelcoat surface. The stainless steel shell reaches the site with an overflow channel and hydraulic pre-installation.
- Galvanised steel panel and liner
- One-piece polyester shell
- AISI 316L stainless steel shell
04
Sizing filtration and equipment
In a residential pool the aim is to pass the entire water volume through the filter every 6 hours; the pump flow rate follows from this. The sand filter is selected for this flow, and one skimmer is planned for every 25 m² of water surface.
- Water volume and 6-hour turnover
- Pump flow rate and filter diameter
- Number of skimmers and pipe diameter
// 01 · Prefabricated pool models
There are six prefabricated pool models, and we choose by site.
We install six residential and hotel prefabricated pool models: steel panel pool, monoblock polyester pool, stainless steel pool, commercial panel pool, overflow panel pool and plunge pool. The model is chosen during the survey according to size, site access and use.

01 / 06
Steel panel pool
Galvanised panels are bolted together on site.
- Shell
- Galvanised steel panel
- Finish
- PVC liner
- Installation
- Assembly on site
- Size
- Flexible by panel module
Galvanised steel panels are bolted together on a raft base, secured with braces and finished with a PVC liner. Because the panels arrive in sizes that can be carried by hand, the pool can also be installed in gardens that trucks and cranes cannot reach.
Suitable forVilla and residential gardens
View in detail: Steel panel poolGalvanised panels are bolted together on site.

- Shell
- Galvanised steel panel
- Finish
- PVC liner
- Installation
- Assembly on site
- Size
- Flexible by panel module
Galvanised steel panels are bolted together on a raft base, secured with braces and finished with a PVC liner. Because the panels arrive in sizes that can be carried by hand, the pool can also be installed in gardens that trucks and cranes cannot reach.
Suitable forVilla and residential gardens
View in detail: Steel panel pool
01 / 06Steel panel pool
- Shell
- Galvanised steel panel
- Finish
- PVC liner
- Installation
- Assembly on site
- Size
- Flexible by panel module
Galvanised steel panels are bolted together on a raft base, secured with braces and finished with a PVC liner. Because the panels arrive in sizes that can be carried by hand, the pool can also be installed in gardens that trucks and cranes cannot reach.
Suitable forVilla and residential gardens
View in detail: Steel panel poolMonoblock polyester pool
- Shell
- Glass fibre reinforced polyester
- Finish
- Gelcoat surface
- Installation
- Placement by crane
- Size
- Limited to mould size
The glass fibre reinforced polyester shell is produced in one piece in the factory and finished with gelcoat. The shell is lowered by crane into the prepared pit; size, steps and depth are part of the mould.
Suitable forResidential gardens with good access
View in detail: Monoblock polyester poolStainless steel pool
- Shell
- AISI 316L stainless steel
- Finish
- Uncoated steel surface
- Installation
- Placement by crane
- Size
- 5-12 m long, 3 m wide
A one-piece shell in 2 mm AISI 316L stainless steel arrives with an overflow channel and non-slip floor. Because hydraulic pre-installation is done, connection and commissioning on site take little time.
Suitable forVilla, terrace and hotel
View in detail: Stainless steel poolCommercial panel pool
- Shell
- Hot-dip galvanised panel
- Finish
- Reinforced PVC membrane
- Installation
- Anchored panel assembly
- Size
- Up to 5 m deep
Hot-dip galvanised steel panels are fixed to the base with chemical anchors, and the inner surface is finished with a 1.5 mm reinforced PVC membrane. The panel system reaches depths of up to 5 m and meets semi-Olympic and Olympic dimensions.
Suitable forHotel, public and sports facilities
View in detail: Commercial panel poolOverflow panel pool
- Shell
- Galvanised steel panel
- Finish
- Liner or ceramic tile
- Installation
- Assembly on site
- Size
- Flexible by panel module
An overflow channel is built at the top level of the panel shell, and the overflowing water is collected in a balance tank and returned to the filter. The balance tank is sized at 60-80 litres per m² of water surface; the plant room is larger than in a skimmer system.
Suitable forVilla and hotel
View in detail: Overflow panel poolPlunge pool
- Shell
- Panel or monoblock
- Finish
- Liner or gelcoat
- Installation
- Assembly on site
- Size
- Around 2.50 × 5 m
A plunge pool of around 2.50 × 5 m is built not for swimming but for stepping in and cooling off. With its small water volume it heats quickly, needs little chemical treatment and is quick to maintain.
Suitable forSmall gardens and courtyards
View in detail: Plunge pool// 01 · Preliminary sizing
Enter the pool dimensions, and let us size the equipment together.
Enter the length, width and average depth of the pool; water volume, pump flow rate, filter diameter, number of skimmers, liner area and raft concrete are calculated instantly.
Calculation rule: water volume = length × width × (average depth − 0.15 m); the water level is taken as 15 cm below the coping. Pump flow rate = volume ÷ 6 hours; filter area = flow ÷ 50 m³/h·m², and the diameter is the standard vessel that meets this area. One skimmer is planned for every 25 m² of water surface. Raft 15 cm; excavation includes a 60 cm working margin on each side and 30 cm of blinding concrete and gravel below the base. Final values are confirmed in the survey and the construction project.
Get a quotation with these dimensions
Send us the pool dimensions and site conditions; we will confirm the shell system, equipment and ground preparation during the survey and prepare an itemised quotation.
| Item | Value |
|---|---|
| Water surface | 32.0 m² |
| Water volume | 40.0 m³ |
| Pump flow rate (6-hour turnover) | 6.7 m³/h |
| Required filter area | 0.13 m² |
| Recommended sand filter diameter | Ø 500 mm |
| Number of skimmers | 2 pcs |
| Liner area (floor and walls) | 65.6 m² |
| Coping length | 24.0 m |
| Raft concrete (15 cm) | 4.8 m³ |
| Excavation volume | 88.5 m³ |
// 01 · Shell layers
A panel pool wall has five layers, and the liner holds the water.
We build the wall from inside to outside with the liner, protective felt, galvanised steel panel, braces and struts, and backfill. The panel carries the load, the liner provides watertightness, and backfill is placed layer by layer as the pool is filled.

- Liner0.75 mm PVC or 1.5 mm reinforced membrane; holds the water.
- Protective feltGeotextile felt; keeps the liner from rubbing on the panel.
- Steel panelHot-dip galvanised steel; carries the shell.
- Braces and strutsTie the panel to the raft and resist backfill pressure.
- BackfillCompacted layer by layer as the pool is filled.
// Reading plan
Before building a prefabricated pool, read these six short articles.
The order follows the natural flow of a prefabricated pool decision: first the systems, then ready-made shells, the comparison with concrete, depth, plumbing and finishes.
Prefabricated pool guide
Panel, fibreglass and polyester systems in one article.5 minShort answer
Prefabricated is the common name for all systems whose shell is produced in a factory; monoblock describes only the one-piece shell. With a one-piece shell the real limit is not the product but whether the shell can enter the garden.
- 01Excavation and raftDays 2-4Excavation, levelling, drainage line and a raft base set true to level
- 02Panel assemblyDays 1-3Bolted panel joints, braces and levelling of the shell
- 03Liner and sealingDays 1-2Underlay felt, liner fitting, skimmer and nozzle gaskets
- 04CommissioningDays 1-3Balanced backfill during filling, leak test and filtration setup
Ready-made, fibreglass and polyester pools
Advantages and limits of a one-piece shell.8 minShort answer
Fibreglass and polyester shells come from the mould, and site work is measured in days. Sizes are limited to the ready-made models; if there is no truck and crane access, the panel system is the right answer.
Concrete or prefabricated
A comparison by lifespan, cost and site conditions.9 minShort answer
With a short schedule and standard size, prefabricated comes first; groundwater, a special form and an overflow channel favour reinforced concrete. In a liner pool the membrane is renewed every 8-12 years.
Depth of a ready-made pool
Why depth does not change in a monoblock shell.8 minShort answer
In a monoblock shell the depth is part of the mould; cutting the floor to deepen it compromises the structural integrity of the shell. If a different depth is needed, the model or system changes.
Pool plumbing and plant room
From turnover time to pump, filter and pipe diameter.9 minShort answer
In a residential pool the water passes through the filter every 6 hours; a 75 m³ pool needs a flow of 12-13 m³/h. For a residential skimmer pool, 4-6 m² is enough for the plant room.
Pool finish options
Differences between liner, ceramic tile and glass mosaic.5 minShort answer
A liner is both the waterproofing and the finished surface; it is quick and economical and is renewed at intervals. In heavily used pools, hard surfaces such as ceramic tile and mosaic come forward in the long term.
Showroom
Plan a showroom visit
At our showroom in Çilek Plaza, Sancaktepe, you can discuss your project with our team. We recommend booking an appointment by phone before your visit.
Working Hours
- Monday to Friday · 08:00-17:30
- Saturday · 08:00-12:30
- Closed on Sunday
// 02 · Cost
Prefabricated pool cost has two drivers, the system and the site.
In prefabricated pool construction the budget is set not only by the shell but by site access, ground conditions and equipment scope. When comparing prefabricated pool prices and quotations from different companies, the six factors below explain why two quotations differ; the final amount is confirmed by an itemised quotation after the survey.
Shell system
A panel, monoblock or stainless shell is the main budget item.
Size and depth
Water volume scales panels, liner, filter and chemical quantities.
Finish class
0.75 mm liner, 1.5 mm reinforced membrane or gelcoat surface.
Site access
Trucks, cranes, narrow streets; key to one-piece shell transport.
Ground and drainage
Groundwater, raft and sump are set by the soil investigation.
Equipment and surrounds
Pump, filter, heating, coping and decking widen the scope.
In-depth reading
- Why Do Pool Quotes Differ So Much? The Choices That Change Your Budget
- 2026 Pool Construction Cost: Per m² and Itemized Budget
- Concrete vs Prefab Pool? 2026 Comparison & Decision Guide
- Pool Running Costs: How to Calculate the Annual Figure Item by Item

// 03 · Process
A prefabricated pool is built in twelve steps, each one resting on the previous.
The process starts with feasibility and model selection, continues with factory production and the raft base, and takes shape with assembly and the liner. We hand over the pool after balanced backfill, the leak test and commissioning.
Survey and design
Feasibility, model and size selection, cost plan
Approved project and itemised quotation
Production and foundation
Factory production, excavation, raft base and drainage
Level raft and the shell delivered to site
Assembly and finish
Panel or monoblock assembly, liner, electromechanical installation
Watertight shell and connected plumbing
Handover
Balanced backfill, coping and decking, leak test, commissioning
Commissioned pool
The twelve steps in detail

01 / 12
Preliminary Survey & Feasibility
Free Online Pre-Consultation
The first step in a prefabricated pool project is reading the site correctly against what a prefabricated system demands. The Çilek Havuz technical team assesses the dimensions of the area, its intended use, the ground structure and the access conditions with you in an online meeting.
At this stage the pool's location, approximate dimensions, crane or plant access, plant-room position, drainage needs and groundwater level are clarified. The fast installation that is the greatest advantage of a prefabricated system is only possible with sound feasibility work.
- Site dimensions and intended use
- Ground bearing capacity
- Crane / plant access
- Drainage and groundwater conditions
- Plant-room location
- Suitability for a prefabricated system
- Zoning and permit requirements
- Preliminary budget and build scenario
Why it matters
The fast-installation advantage of a prefabricated pool becomes real only when the ground and access conditions have been read correctly. Where feasibility is skipped, mistakes in crane access, drainage or ground conditions lead to delay and additional cost later in the process.
// 04 · Shell and finish materials
We choose separate materials for shell and surface, because one carries and the other holds water.
For the load-bearing shell we use galvanised steel panels, glass fibre reinforced polyester or stainless steel; for the water-holding surface, PVC liner, reinforced membrane or gelcoat. For the coping we choose porcelain tiles with a non-slip surface.
01Galvanised steel panel
S235JR steel panels are hot-dip galvanised; the coating protects the panel against corrosion. Panels arrive 1 m wide and are joined with bolts.
Used in
- Shell
- Panel
02Glass fibre reinforced polyester
A light, corrosion-resistant shell laminated layer by layer in the mould. Steps and seating areas come as part of the mould.
Used in
- Monoblock shell
03AISI 316L stainless steel
The one-piece 2 mm shell needs no separate finish, and its surface is hygienic. The overflow channel and non-slip floor are produced together with the shell.
Used in
- Shell
- Overflow channel
04PVC liner
Flexible 0.75 mm PVC is both the waterproofing and the finished surface. The membrane is renewed every 8-12 years while the panel shell stays in place.
Used in
- Finish
- Waterproofing
05Reinforced PVC membrane
A 1.5 mm membrane with a polyester mesh between two PVC layers. It is hot-air welded on site; we prefer it for heavily used pools.
Used in
- Finish
- Commercial pool
06Gelcoat
The smooth, jointless surface of the polyester shell, applied in the factory; it holds little dirt and is easy to clean. When the water chemistry is kept balanced, it keeps its colour for a long time.
Used in
- Monoblock surface
07Porcelain tile coping
Porcelain with low water absorption resists frost and chemicals. At the pool edge we use pieces with a non-slip surface.
Used in
- Coping
- Overflow channel
// 04 · Prefabricated pool materials
From the shell to the filter, we choose materials by pool volume.
One-piece stainless steel pools, commercial panel pool systems, liners, pumps and filters are among our products. You can review the size, material and technical values of each product on its own page.
// 05 · Projects
From villas to residential complexes, the prefabricated pools we have built.
We gather the prefabricated pool projects we have delivered here. In each project the shell system, ground preparation and filtration were determined separately for the site.
// 05 · Service regions
Across Türkiye and abroad, we install prefabricated pools.
We carry out prefabricated pool construction in villa, residential and hotel projects across Türkiye; we export to 14 countries and run projects abroad on site through our branches in Kyrgyzstan, Egypt, Algeria and Iraq.
Domestic
15- Istanbul
- Mugla / Bodrum
- Antalya
- Izmir / Cesme
- Ankara
- Bursa
- Kocaeli / İzmit
- Adana
- Mersin
- Tekirdağ
- Kandıra
- Sakarya
- Samsun
- Denizli
- Elazığ
International
13- AlgeriaBranch
- EgyptBranch
- IraqBranch
- KyrgyzstanBranch
- France
- Germany
- Kazakhstan
- Libya
- Qatar
- Russia
- Saudi Arabia
- United Arab Emirates
- United Kingdom
// 06 · After handover
The work does not end at handover, we continue maintenance together.
At handover we set the filtration and water balance together and explain how backwashing and liner care are done. Our workmanship carries a 2-year warranty.
- 012 years
Warranty
Our construction workmanship is covered for 2 years from handover; warranty documents are issued at handover.
- 021-3 days
Commissioning and training
We check the leak test and the operation of the pump and filter, set the water balance and explain use on site.
- 03Weekly
Water and filter
pH and chlorine are measured weekly; when filter pressure rises the filter is backwashed and skimmer baskets are emptied.
- 04Seasonal
Liner and winterising
Before winter the water level and chemicals are adjusted; the liner surface and gaskets are checked at the start of the season.
Related services
- Swimming Pool ConstructionReinforced-concrete, prefabricated and infinity swimming pools, built turnkey for villa, residential and commercial projects.
- Infinity PoolsPools that open onto the view, with water spilling over the edge into a balance tank.
- Natural PondsNatural-look pond and bio-pool designs.
- Ornamental PoolsDecorative water features with fountains, cascades and lighting.
- Thermal PoolsDurable pool systems built for thermal water.
- Aquapark ConstructionWater parks with slides for hotels, holiday resorts and municipalities.
Prepared byAli SAVAŞ · Project Manager · Mechatronics Engineer
// 07 · Questions
About prefabricated pool construction, frequently asked questions.
Çilek Havuz Corporate
Pool & Wellness Engineering
- Response Time
- Same day
- Channels
- Phone · Email · WhatsApp
If the answer you are looking for is not here, send your question directly to us and our team will reply as soon as possible.
+90 216 475 39 37Installing a prefabricated pool takes less time than a concrete pool. The duration is given in writing during the survey according to ground preparation, the factory production schedule and equipment scope.
Çilek Havuz Corporate
Prefabricated is the common name for all systems whose shell is produced in a factory; a ready-made or monoblock pool describes the one-piece shell. The panel system is also prefabricated but is assembled on site; the quotation should state clearly which one is meant.
Çilek Havuz Corporate
If a truck and crane can enter the garden and a ready-made model size is enough, a polyester pool suits. If access is narrow or the size is custom, a panel pool suits. The panel system gives flexibility in size and is finished with a liner; the polyester shell comes in one piece with a gelcoat surface.
Çilek Havuz Corporate
Prefabricated pool prices are determined by the shell system, size, finish class, site access, ground preparation and equipment package. We recommend comparing not on shell price but on the total scope including excavation and plumbing.
Çilek Havuz Corporate
Yes, the panel system does not need truck or crane access; panels arrive in sizes that can be carried by hand. A one-piece polyester or stainless shell cannot be installed without crane access; access is measured on site during the survey.
Çilek Havuz Corporate
In residential prefabricated pools the most common depth is 1.40-1.50 m; commercial panel systems reach depths of up to 5 m. In a monoblock shell the depth is part of the mould and is not changed on site.
Çilek Havuz Corporate
In a liner pool the membrane is renewed every 8-12 years. Unbalanced pH and high chlorine shorten its life; replacement is done with the panel shell kept in place.
Çilek Havuz Corporate
In residential pools 0.75 mm PVC liner is the common standard; in heavily used pools a 1.5 mm reinforced membrane is used. The reinforced membrane carries a polyester mesh between two PVC layers and is hot-air welded on site.
Çilek Havuz Corporate
After excavation and levelling, the pool sits level on a reinforced concrete raft base. Blinding concrete and gravel are laid under the raft; the drainage line and, if needed, a sump are planned from the start.
Çilek Havuz Corporate
It can, but drainage and a sump must be planned in the project from the start. A light shell left empty can be shifted by the uplift of groundwater; for this reason a soil investigation is essential.
Çilek Havuz Corporate
The pump flow rate is chosen so that the water volume passes through the filter every 6 hours. A 5 × 10 m pool with a water depth of 1.50 m holds 75 m³ and runs with a flow of 12-13 m³/h and a Ø600 mm sand filter.
Çilek Havuz Corporate
One skimmer is planned for every 25 m² of water surface; a 5 × 10 m pool uses two skimmers. Skimmer positions are set during the survey according to the prevailing wind direction and the pool form.
Çilek Havuz Corporate
Yes, prefabricated shells are compatible with heat pumps and heat exchangers. Planning heating into the plant room design from the start avoids later plumbing and electrical rework.
Çilek Havuz Corporate
Çilek Havuz builds prefabricated pools in villa, residential and hotel projects across Türkiye. We export to 14 countries and run projects abroad through our branches in Kyrgyzstan, Egypt, Algeria and Iraq.
Çilek Havuz Corporate
// Sources and regulations
Sources and regulations
The official documents behind the technical framework on this page; links open the institutions' own sites.
- Regulation on the Health Principles and Conditions for Swimming Pools (Official Gazette No. 27866, 6 March 2011)Official Gazette of Türkiye
- Regulation Amending the Swimming Pools Regulation (Official Gazette, 15 December 2011)Official Gazette of Türkiye
- Guidelines for safe recreational water environments, Volume 2: Swimming pools and similar environments
Next step
Let us discuss your project in the way that suits you best.
You can fill in the form for a written quote, schedule a video project presentation or ask us to survey your project site.
Get a Quote
Send us your dimensions and expectations in writing.
Online presentation
Video project presentation
On-site survey
Inspection at your project site
// 08 · Company & Contact
To talk about your project, call or write to us.
Legal Name
Çilek Havuz
Founded
1998 · Istanbul
Head Office
Çilek Plaza, Eyüp Sultan Mah. Yakacık Cd. Feshane Cd. No: 2 D:4 D:1, 34885 Sancaktepe / İstanbul
Service Area
All of Türkiye · exports to 14 countries
Branches
Kyrgyzstan · Egypt · Algeria · Iraq
Showroom
Plan a showroom visit
At our showroom in Çilek Plaza, Sancaktepe, you can discuss your project with our team. We recommend booking an appointment by phone before your visit.
Working Hours
- Monday – Friday · 08:00 – 17:30
- Saturday · 08:00 – 12:30
- Closed on Sunday




















